Lindy 52053 User Manual

IEEE 802.11n Wireless LAN PCI Adapter User’s Manual October 2010

9 STEP3: Please read the following license agreement. Use the scroll bar to view the rest of this agreement. Select I accept the terms of

10STEP5: In Windows XP, there is a Windows Zero Configuration Tool for you to setup wireless adapter. You can choose to configure

11STEP7: Please wait for a while during the Wireless LAN adapter is configuring your new software installation. STEP8: After the setu

12The Configuration Utility appears as an icon on the system tray of Windows while the adapter is running. You can open the utility by

133. Wireless Network Configuration Utility 3.1 RaUI Wireless Utility & Windows Zero Configuration (WZC) The Configuration Utility is a powerfu

14 When activating WZC, there are couple different on RaUI status compare to the without WZC running: (1) Profile button will be gr

15 STEP3: All wireless access point in proximity will be display here. If the access point you want to use is not display here, please try to move yo

16 STEP5: When you see the “Connected” message, the connection between your computer and wireless access point is successfully established

17STEP7: Choose “Wireless Networks” tab. STEP8: Click “Properties” and then click “OK” button. STEP9: After filling appropriate value, click “O

18STEP10: Click the Ralink’s icon will bring up RaUI main window. User can find the surrounding APs in the list. The current con

1 FCC Warning This equipment has been tested and found to comply with the limits for a Class C digital device, pursuant to part 15 of

19 There are three sections in RaUI. These sections are briefly described as below.  Button Section: Include Profile page, Network page, Advanced

20 Function Section: Corresponding button  Profile Page  Network Page  Advanced Page

21  Statistics Page  WMM Page  WPS Page

22  SSO Page (available on Windows XP & 2000 OS)  CCX Page (available on Windows Vista, XP & 2000 OS)  About Page

23 Status Section: Include Link Status, Authentication Status, AP’s information, Configuration and retrying the connection when authenticat

24  Retry the Connection  Configuration  At the mean time of starting RaUI, there is also a small Ralink icon appears within windows t

253.3 Profile Profile can book keeping your favorite wireless setting among your home, office, and other public hot-spot. You may save multiple

26  Delete an existing profile  Activate selected profile  Show the information of Status Section  Hide the information of Status Section

27signal reception), you can select a lower output power to save energy; for a distant access point, you can select a higher output power. It

28 Step 2: Add Profile page will pop up. Step 3: Change profile name to what you want to connect. Pull down the SSID and select one intended AP.

2 IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter

29Step 4: To set authentication/encryption information for the access point, please click “Auth.\Encry.” Tab. Step 5: Then, you can see

30[Definition of each field] Sorted by >>: You can decide how to sort all listed access point by SSID, Channel, Signal (Signal

31(2) If user wants to connect to other AP, He can click “Connect: button for the intended AP to make connection. (3) If the intended network h

32 Figure 2: Country Channel list Apply: Save the save changes  Show the information of Status Section  Hide the information of Status Section

333.6 Statistics The configuration utility provides information about network statistics and link status. If you want to know how your wireless

343.7 WMM This wireless network card provides WMM (Wi-Fi Multimedia) function, which can improve the performance of certain network applications

35 Step 2: Change to “Network” function. And add an AP that supports WMM features to a Profile. The result will look like the below fig

36 Step 2: Please select which ACs you want to enable. The setting of enabling WMM-Power Save is successfully. [Direct Link Setup Enable –

37 The Setting of DLS indicates as follow: (1) Fill in the blanks of Direct Link with MAC address of STA. The STA must conform to 2 con

38(2) Timeout Value represent that it disconnect automatically after some seconds. The value is integer. The integer must be between 0~65535. It rep

3 Contents 1. Introduction ... 4 1.1 Features ...

39 Step 2: Double-Click and the result will look like the below figure. (3) Disconnect Direct Link Setup as follow: Step 1: Select a direct l

40 Step 2: Click “Tear Down” button. The result will look like the below figure. 3.8 WPS Wi-Fi Protected Setup (WPS) is the latest wireless networ

41WPS Configuration: The primary goal of Wi-Fi Protected Setup (Wi-Fi Simple Configuration) is to simply the security setup and management of Wi-Fi n

42Progress Bar: Display rate of progress from Start to Connected status. Status Bar: Display currently WPS Status. [WPS Information on AP] WPS info

43Device Password ID: Indicate the method or identifies the specific password that the selected Registrar intends to use. AP in PBC mode

44 Use ID and Password in Profile: Use the ID and Password in RaUI Profile settings.  Prompt ID and Password Dialog: Use the ID and Pass

453.11 About About function display the wireless card and driver version information. (1) Connect to Ralink’s Website: WWW.RALINKTECH.COM (2) Di

46Link Speed: Show current transmit rate and receive rate. Throughout: Display transmits and receive throughput in unit of Mbps. Link Quality: Di

47A configuration window will appear after you switch the operation mode to ‘AP’, which asks you to assign an existing network card with internet con

48Security Setting: Set the security options (wireless data encryption). Please refer to chapter 4-2 ‘Security Settings’ for details. Country Region

4 1. Introduction Thank you for purchasing this high-speed wireless network card! Excepting common wireless standards 802.11b/g, this wireless n

494.2 Security Settings Authentication Type: Please select a wireless authentication type you wish to use. Available options are ‘Open’, ‘Shared’

50is safer then 64 bits, but the data transfer speed will be slightly reduced. Show Password: Check this box and the WPA pre-shared key or WEP key yo

51No colon (:) or hyphen (-) required. Add: Add the MAC address you inputted in ‘MAC address’ field to the list Delete: Please select a MAC address f

52 4.6 Statistics If you want to know detailed information about how your software access point works, click ‘Statistics’ tab, and the event log wil

534.7 About The ‘About’ tab provides you the information about version number of the configuration utility, driver, and other important i

5 1.4 Before you start You must have the requirements as follow, ‧ A computer with an available PCI slot ‧ At least a 300MHz processor and 32MB m

6 STEP3: Secure this card to the rear of the computer chassis and replace the cover. STEP4: Install the antenna on the wireless network card,

7 2. Installation Procedure Note: If you have installed the Wireless Adapter driver & utility before, please uninstall the old version first. S

8 (For Windows 2000) STEP2: Insert Installation CD into CD-ROM drive, windows below will appear. Click Install Driver & Utility to